INSTALLATION INSTRUCTIONS
Our installation instructions are designed to guide enthusiasts of all skill levels through the process, making it accessible and enjoyable. However, for the best results and to preserve the integrity of your graphics, we strongly recommend seeking the expertise of a professional installer. While our instructions are comprehensive, a trained hand can provide precision and attention to detail that may be challenging for first-time installers.
Remember, your vehicle is a reflection of your style, and we want your graphics to enhance its aesthetics flawlessly. If you choose to go the DIY route, follow the step-by-step instructions diligently. If, however, you prefer the assurance of professional hands, consult with a skilled installer in your area.
INSTALLATION GUIDES
Prepare the Vehicle Surface:
Ensure the vehicle surface is clean, dry, and free from dust or debris. Mix water and a small amount of mild detergent in a spray bottle. Lightly spray the vehicle surface with the soapy water solution.
Position and Apply the Graphics:
Carefully peel off the backing paper from the graphics, exposing the adhesive side. Position the graphics on the wet vehicle surface, allowing you to slide and adjust them for proper alignment.
Smooth Out Air Bubbles:
Gently use a squeegee to smooth out any air bubbles from the center to the edges of the graphics.
Wait 2-3 Hours:
Allow the applied graphics to set and adhere to the vehicle surface for 2-3 hours before proceeding to the next step.
Trim Excess Material:
Once the graphics have set, use scissors or a utility knife to trim any excess material along the edges of the vehicle. Ensure a clean and precise cut.
Trim at Door Seams:
With the graphics applied, carefully trim the material at the door seams using scissors or a utility knife. Ensure a clean and precise cut to enhance the overall appearance.
Remove Application Tape:
Peel off the application tape at a 45-degree angle, pulling it back over itself. This should be done slowly and evenly to avoid lifting the graphics.
Final Inspection:
Inspect the graphics for any remaining air bubbles or imperfections. If necessary, use a pin or needle to puncture and release trapped air, then smooth out the area.
Allow Full Cure Time:
For optimal adhesion and longevity, avoid washing or exposing the vehicle to extreme conditions for at least 2-4 days after installation.
Prepare the Vehicle Surface:
Clean the vehicle hood thoroughly using a mild soapy water solution and a clean, lint free cloth. Rinse the surface with clean water and allow it to dry completely before proceeding.
Positioning the Graphics:
Place the vehicle graphics on the hood without removing the backing paper. Use low-tack painter's tape to temporarily secure the graphics in the desired position. Ensure proper alignment and spacing.
Wet Application:
Mix a mild soapy water solution in a spray bottle. Lightly mist the vehicle hood with the soapy water solution. Peel off a small section of the backing paper from the graphics, exposing the adhesive side.
Apply Graphics:
Align the exposed section of the graphics with the desired position on the hood. Use a squeegee or a credit card wrapped in a soft cloth to smooth out the graphics from the center to the edges. This helps remove air bubbles and excess water.
Continue Application:
Gradually peel off the backing paper, applying the graphics and smoothing out any bubbles or wrinkles as you go. If needed, use additional soapy water to facilitate smooth application.
Wait 2-3 Hours:
Allow the applied graphics to set and adhere to the vehicle surface for 2-3 hours. This time is crucial for a secure bond between the graphics and the vehicle.
Remove Application Tape:
Once the graphics are fully applied, gently peel off the application tape at a 45-degree angle. This should be done slowly and carefully to avoid lifting the graphics.
Final Inspection:
Inspect the installed graphics for any imperfections or edges that may need additional attention. If necessary, use a squeegee or your fingers to smooth out any remaining air bubbles.
Allow Full Cure Time:
For optimal adhesion and longevity, avoid washing or exposing the vehicle to extreme conditions for at least 2-4 days after installation.
Prepare the Vehicle Surface:
Ensure the vehicle surface is clean, dry, and free from dust or debris. Mix water and a small amount of mild detergent in a spray bottle. Lightly spray the vehicle surface with the soapy water solution.
Position the Graphic
Carefully position the graphic on the truck bed surface without removing the backing. Use small pieces of masking tape to hold the graphic in place if needed.
Wet the Surface
Liberally spray the entire truck bed surface with the water and detergent mixture. This will create a wet surface for the graphic to adhere to.
Remove the Backing
Starting from one corner, gently peel off the backing of the graphic. Be sure to keep the graphic wet by continuously spraying the exposed adhesive side with the water and detergent mixture.
Apply the Graphic
Once the backing is removed, carefully position the graphic onto the wet truck bed surface. The water will allow you to slide and adjust the graphic for proper alignment.
Squeegee Out Air Bubbles
Use a squeegee or applicator tool to smooth out the graphic, working from the center and moving towards the edges. This will help eliminate any air bubbles and ensure a secure bond between the graphic and the truck bed.
Wait 2-3 Hours
Allow the applied graphics to set and adhere to the vehicle surface for 2-3 hours before proceeding to the next step. This ensures proper adhesion and minimizes the risk of graphic displacement.
Trim Excess Material
After the waiting period, use scissors or a utility knife to carefully trim any excess material along the edges of the vehicle. Ensure a clean and precise cut for a professional finish.
Remove Application Tape
Peel off the application tape at a 45-degree angle, pulling it back over itself. This should be done slowly and evenly to avoid lifting the graphics. Take your time and ensure that the graphic is fully adhered to the truck bed.
Final Inspection:
Inspect the graphics for any remaining air bubbles or imperfections. If necessary, use a pin or needle to puncture and release trapped air, then smooth out the area.
Allow Full Cure Time:
For optimal adhesion and longevity, avoid washing or exposing the vehicle to extreme conditions for at least 2-4 days after installation.
Preparation:
Park your vehicle in a shaded area to avoid direct sunlight, which can make the
installation challenging.
Ensure the rear window is clean and free from dust, dirt, and grease. Clean the surface using isopropyl alcohol or a mild cleaning solution.
Measuring and Alignment:
Carefully measure your rear window and the perforated graphic to ensure a proper fit.
Use masking tape to temporarily secure the graphic in place and make any necessary adjustments to the alignment.
Peeling the Backing:
Begin by peeling a small section (2-3 inches) of the backing from the top edge of the graphic.
Fold the backing down, creating a hinge that will help you position the graphic accurately.
Application:
Position the exposed adhesive portion of the graphic onto the top edge of the rear window, aligning it with the previously marked guidelines.
Use the squeegee to smooth out the graphic, starting from the center and working your
way towards the edges. This will help eliminate air bubbles and ensure a secure bond.
Gradual Peeling and Squeegeeing:
Gradually peel away the backing, applying even pressure with the squeegee as you go.
Continue working from the center towards the edges, ensuring a smooth and bubble free application.
Trimming Excess Material:
Once the entire graphic is applied, use a utility knife or scissors to trim any excess
material along the edges of the rear window.
Take your time and follow the contours of the window for a clean and professional finish.
Final Inspection:
Carefully inspect the entire graphic for any bubbles or imperfections. If necessary,
gently lift the affected area and reapply.
Curing Time:
Allow the installed graphic to cure for at least 3-4 days before exposing it to harsh weather conditions.
TIPS FOR FLAWLESS VEHICLE GRAPHIC INSTALLATIONS
Extreme temperatures can affect the adhesive properties of the graphics. Recommend a temperature range for installation, typically between 50°F and 90°F (10°C to 32°C). Advise users to avoid installing graphics in direct sunlight or very cold conditions.
Ensure that the vehicle surface is thoroughly cleaned before starting the installation. Any dust, dirt, or wax can affect adhesion.
Create a mild soap solution by mixing a few drops of dish soap with water. This solution will act as a lubricant during the application.
Spray the vehicle surface and the adhesive side of the graphic with the soap solution. This allows for repositioning and reduces the risk of premature adhesion.
Take your time to position the graphic correctly. The wet method allows adjustments, so ensure it's aligned perfectly before squeegeeing out excess water.
Use a soft squeegee to smooth out the graphic from the center towards the edges. This helps eliminate air bubbles and excess water.
Divide the graphic into manageable sections for easier handling. Apply the wet method
to one section at a time, ensuring each part is properly adhered before moving on.
Maintain even pressure while squeegeeing to avoid wrinkles or bubbles. Pay extra attention to corners and edges, ensuring they are firmly pressed down.
Periodically check for air bubbles during the installation. If you notice any, lift the graphic slightly and reapply using the squeegee.
Allow the graphic to set and adhere properly before removing any application tape. Rushing this process may result in the graphic not adhering securely.
After the installation is complete, Inspect the graphics for any remaining air bubbles or imperfections. If necessary, use a pin or needle to puncture and release trapped air, then smooth out the area.